Binary prefix

Prefixes for decimal and binary multiples
Decimal
Value SI
1000 103 k kilo
10002 106 M mega
10003 109 G giga
10004 1012 T tera
10005 1015 P peta
10006 1018 E exa
10007 1021 Z zetta
10008 1024 Y yotta
10009 1027 R ronna
100010 1030 Q quetta
Binary
Value IEC JEDEC
1024 210 Ki kibi K kilo
10242 220 Mi mebi M mega
10243 230 Gi gibi G giga
10244 240 Ti tebi T tera
10245 250 Pi pebi
10246 260 Ei exbi
10247 270 Zi zebi
10248 280 Yi yobi

A binary prefix is a unit prefix that indicates a multiple of a unit of measurement by an integer power of two. The most commonly used binary prefixes are kibi (symbol Ki, meaning 210 = 1024), mebi (Mi, 220 = 1048576), and gibi (Gi, 230 = 1073741824). They are most often used in information technology as multipliers of bit and byte, when expressing the capacity of storage devices or the size of computer files.

The binary prefixes "kibi", "mebi", etc. were defined in 1999 by the International Electrotechnical Commission (IEC), in the IEC 60027-2 standard (Amendment 2). They were meant to replace the metric (SI) decimal power prefixes, such as "kilo" ("k", 103 = 1000), "mega" ("M", 106 = 1000000) and "giga" ("G", 109 = 1000000000),[1] that were commonly used in the computer industry to indicate the nearest powers of two. For example, a memory module whose capacity was specified by the manufacturer as "2 megabytes" or "2 MB" would hold 2 × 220 = 2097152 bytes, instead of 2 × 106 = 2000000.

On the other hand, a hard disk whose capacity is specified by the manufacturer as "10 gigabytes" or "10 GB", holds 10 × 109 = 10000000000 bytes, or a little more than that, but less than 10 × 230 = 10737418240 and a file whose size is listed as "2.3 GB" may have a size closer to 2.3 × 2302470000000 or to 2.3 × 109 = 2300000000, depending on the program or operating system providing that measurement. This kind of ambiguity is often confusing to computer system users and has resulted in lawsuits.[2][3] The IEC 60027-2 binary prefixes have been incorporated in the ISO/IEC 80000 standard and are supported by other standards bodies, including the BIPM, which defines the SI system,[1]: p.121  the US NIST,[4][5] and the European Union.

Prior to the 1999 IEC standard, some industry organizations, such as the Joint Electron Device Engineering Council (JEDEC), attempted to redefine the terms kilobyte, megabyte, and gigabyte, and the corresponding symbols KB, MB, and GB in the binary sense, for use in storage capacity measurements. However, other computer industry sectors (such as magnetic storage) continued using those same terms and symbols with the decimal meaning. Since then, the major standards organizations have expressly disapproved the use of SI prefixes to denote binary multiples, and recommended or mandated the use of the IEC prefixes for that purpose, but the use of SI prefixes has persisted in some fields.

While the binary prefixes are almost always used with the units of information, bits and bytes, they may be used with any other unit of measure, when convenient. For example, in signal processing one may need binary multiples of the frequency unit hertz (Hz), for example the kibihertz (KiHz), equal to 1024 Hz.[6][7]

  1. ^ a b Cite error: The named reference BIPM8 was invoked but never defined (see the help page).
  2. ^ Cite error: The named reference suitxxxx was invoked but never defined (see the help page).
  3. ^ Cite error: The named reference sand2021 was invoked but never defined (see the help page).
  4. ^ Cite error: The named reference NIST1 was invoked but never defined (see the help page).
  5. ^ Cite error: The named reference NIST2 was invoked but never defined (see the help page).
  6. ^ Cite error: The named reference pate2011 was invoked but never defined (see the help page).
  7. ^ Cite error: The named reference ains2022 was invoked but never defined (see the help page).

From Wikipedia, the free encyclopedia · View on Wikipedia

Developed by Nelliwinne